AACC

Application Guilelines

Laminator
Application of Adhesives A-5600 & A-5750

Bolton Emerson Americas TL-1060 with Adhesives A-5600 & A-5750

Substrate Conditions:
Board should be smooth, free from surface irregularities, sanded if necessary and then vacuumed to remove dust from the surface to be laminated. Board should not be laminated if temperature of surface is below 65° F. Preheating of boards is recommended for best results during cold weather.
Surface Temperature of Nip Rollers:
300 - 330° F (130-140 psi steam)
Note: Laminating temperatures are a function of several factors: basis weight of paper, speed of lamination, board temperature, etc. and should be determined by the operator for varying conditions.
Nip Pressure (Set-Up):
150-200 lb
Nip Pressure (Run):
500-700 lb
Speed:
40 - 150 FPM
Paper:
23 to 120 gram

Black Brothers TB-60 with Adhesives A-5600 & A-5750

Substrate Conditions:
Board should be smooth, free from surface irregularities, sanded if necessary and then vacuumed to remove dust from the surface to be laminated. Board should not be laminated if temperature of surface is below 65° F. Preheating of boards is recommended for best results during cold weather.
Surface Temperature of Nip Rollers:
300 - 330° F
Note: Laminating temperatures are a function of several factors: basis weight of paper, speed of lamination, board temperature, etc. and should be determined by the operator for varying conditions.
ROLL TEMPERATURE SHOULD BE VERIFIED WITH A PYROMETER.
Nip Pressure (Set-Up):
150-200 lb
Nip Pressure (Run):
500-700 lb
Speed:
40 FPM
Paper:
23 to 30 gram

Evans-Rotork with Adhesives A-5600 & A-5750

Substrate Conditions:
Board should be smooth, free from surface irregularities, sanded if necessary and then vacuumed to remove dust from the surface to be laminated. Board should not be laminated if temperature of surface is below 65° F. Preheating of boards is recommended for best results during cold weather.
Surface Temperature of Steel Rollers:
355 - 375° F
Note: Laminating temperatures are a function of several factors: basis weight of paper, speed of lamination, board temperature, etc. and should be determined by the operator for varying conditions.
ROLL TEMPERATURE SHOULD BE VERIFIED WITH A PYROMETER.
Surface Temperature of Rubber Rollers:
225 - 275° F
Pressure:
90-100 lb
Speed:
20 - 40 FPM
Lamp Setting:
50 - 80%
Distance From Web:
3 - 8 inches
Paper:
23 to 30 gram

Monco with Adhesives A-5600 & A-5750

Substrate Conditions:
Board should be smooth, free from surface irregularities, sanded if necessary and then vacuumed to remove dust from the surface to be laminated. Board should not be laminated if temperature of surface is below 65° F. Preheating of boards is recommended for best results during cold weather.
Surface Temperature of Nip Rollers:
300 - 330° F
Note: Laminating temperatures are a function of several factors: basis weight of paper, speed of lamination, board temperature, etc. and should be determined by the operator for varying conditions.
ROLL TEMPERATURE SHOULD BE VERIFIED WITH A PYROMETER.
Nip Pressure (Set-Up):
150-200 lb
Nip Pressure (Run):
500-700 lb
Speed:
40 FPM
Paper:
23 to 30 gram

Trouble Shooting Hot Melt Lamination

Problem
Possible Solution

Please Note:
The information presented on this web site is only a guideline. Optimal settings will vary depending on many factors, including the maintenance history and condition of your equipment. Operators must evaluate these factors to determine optimal laminating conditions.

Our service engineers are available to help purchasers obtain best results from our products, and recommendations are based on tests and information believed to be reliable. However, since we have no control over the conditions under which our products are transported to, stored, handled, or used by purchasers, all recommendations are made on condition that we will not be held liable for any damages resulting from their use. No representative of ours has any authority to waive or change this provision.